1

I am trying to teleport a player to certain coordinates once they enter an area.

The idea is that they walk into a really small building, but once they turn a corner, they get teleported into a larger building.

Please refer to the adventure map named '5 Cubed', if you need help understanding what I am asking.

Improve this question
3
  • 1
    I think you can just put \tp **** **** **** The asterisk being the x, y, and z coordinates. I'm not 100% positive about that though. Also a pressure plate on a block and a command block under that.
    – zombieatmore
    Commented Mar 24, 2015 at 0:26
  • @zombieatmore This only works in single player. It will only tp the player who uses it. So it is useless for use with command blocks.
    – angussidney
    Commented Mar 25, 2015 at 10:02
  • @AngusAtkinson I wasn't 100% sure if mine was correct either way so.....
    – zombieatmore
    Commented Mar 27, 2015 at 10:01

4 Answers 4

Reset to default
4

1.9 Solution

Place the following command in a repeating command block set to always active:

/execute @a[x=a,y=b,z=c,r=d] ~ ~ ~ tp @p e f g

Where:

  • a, b, and c are the XYZ co-ordinates that you want to teleport players from
  • d is the radius in blocks around that point where players will be selected (min 1)
  • e, f, and g are the XYZ co-ordinates that you want to teleport players to (i.e. the destination)

1.8 Solution

Use the same command as above, but since no repeating command blocks exist, place the command block on a fill clock.

Improve this answer
3
  • Is there a possible way to replace radius with something like, "~ ~ ~"? I'm also looking for a way to test for a player at certain co-ordinates. Is this possible?
    – Jake
    Commented Mar 30, 2015 at 20:32
  • Yes this is possible, however not by the /tp command. Use a /testfor command
    – angussidney
    Commented Mar 31, 2015 at 9:32
  • @Jake Try /testfor @a[x=? y=? z=?], with a comparator pointing out of the command block. This will produce a current when a player is at the certain co-ords.
    – angussidney
    Commented Mar 31, 2015 at 9:35
0

1.13.x solution

If anyone is coming from 1.13.x, the /testfor command has been deleted. In that case if you want to teleport someone you can use the /execute command as thus

/execute if entity @a[x=0,y=0,z=0,distance=..1] run tp @p x y z

The first set of X Y Z coordinates is where you want the player to be teleported from, the second is where you want the player to be teleported to.

Improve this answer
-1

Put pressure plates around your desired area. under each pressure plate place a command block that will teleport you to coordinates of your choice. do this by inserting the command /tp @p x y z into your command block.

Improve this answer
-2

It's actually quite easy:

Just have a command block that is on a clock, and it should constantly testfor a player at certain co-ords:

/testfor @a[x=???,y=???,z=???]

(copy exactly except replace ? with the co-ords) then put a comparater leading out of it to a command block that:

/tp @p ??? ??? ??? (x,y,z).

You can also do:

/test for @a[x=???,y=???,z=???,r=?]

Where r is a radius (i.e. if r is 3 it will test for players within 3 blocks in a directions of the co-ords specified.

Improve this answer
1
  • This does not work. This will just teleport the player closest to the command block when any player enters the coordinates.
    – MrLemon
    Commented Mar 24, 2015 at 16:19

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.